Vna6000p - Revision history

Zyj: /* Product Documentation */

2021-10-06T05:19:51Z

Product Documentation

Zyj at 05:15, 6 October 2021

2021-10-06T05:15:35Z

Zyj at 14:51, 27 September 2020

2020-09-27T14:51:42Z

Zyj at 14:50, 27 September 2020

2020-09-27T14:50:31Z

Zyj: Created page with "VNA6000P is a Portable, full 2-port 6 GHz VNA Main Features ✔ Frequency range: 1 MHz to 6 GHz ✔ Full two-port VNA: both ports can function as transmitter and receiver whic..."

2020-09-27T14:48:03Z

Created page with "VNA6000P is a Portable, full 2-port 6 GHz VNA Main Features ✔ Frequency range: 1 MHz to 6 GHz ✔ Full two-port VNA: both ports can function as transmitter and receiver whic..."

New page

VNA6000P is a Portable, full 2-port 6 GHz VNA
Main Features
✔ Frequency range: 1 MHz to 6 GHz
✔ Full two-port VNA: both ports can function as transmitter and receiver which allows to
measure all four S-parameters without physically switching the DUT
✔ Above capability allows the implementation of standard VNA calibration procedures.
Currently implemented procedures are 1-port OSL, 2-Port OSLT, 2-Port LMR16 and
Transmission normalization for S21/S12. Industry standard models of calibration
standards (separately for male and female connectors) are supported
✔ Due to architecture of this VNA, only one S-parameter can be measured at the time.
Separate 1-Port and 2-Port modes are implemented. In 1-Port mode only S11 or S22 is
measured which allows for faster trace update. In 2-port mode trace is updated after all 4
parameters are measured successively
✔ Currently two traces can be displayed simultaneously which can be set to combination
any of four S-parameters and different data representations which includes: Log
magnitude, Linear reflection coefficient, Impedance, VSWR, Phase, Group Delay. Trace
display range and Ref. level can be changed for all formats
✔ Time Domain(TD) function is available in 1-Port mode. Implemented TD modes: Band-
Pass impulse, Low-Pass impulse ans Low-Pass step. It is possible to zoom and interpolate
data in time axis for increased resolution
✔ Smith chart display is available which can be displayed simultaneously with Cartesian
traces
✔ Two scrollable trace markers are available which includes 'Delta' function as well
✔ User can save data to Micro-SD card. Available data formats are BMP screen-shots, S-
parameters (S1P or S2P files) and OSLT calibration coefficients. SD card also contains
description of calibration standard model coefficients.
✔ Internal ('factory') calibration allows to do quick 1-Port/2-Port measurements without
mechanical calibration
✔ Zero span option allows to use VNA as simple signal generator (unfiltered and level
uncalibrated). On-board step attenuator allows to change signal power in range of 31.75
dB with steps of 0.25 dB
✔ All main settings, when changed, are automatically saved in on-board EEPROM
✔ VNA is powered from single 3200 mA Li-Po cell or +5 to +12Vdc wall adapter and
includes circuit for automatic battery charging. Approximate battery life ranges from 3 to
4 hours depending on measurement mode (on 1-Port mode one channel can be powered
off). Current consumption is operational mode is ranges from 600 to 700 mA, but in
sleep/power off mode less is than 100 uA

@@ Line 48: / Line 48: @@
 == <font color="blue">Product Documentation</font> ==
 * [http://www.mtinst.com/wiki/upload/vna6000p_manual_cn.pdf vna6000p manual cn]
-* [http://www.mtinst.com/wiki/upload/vna6000p_manual.pdf vna6000p manual]
+* [http://www.mtinst.com/wiki/upload/vna6000p_manual_en.pdf vna6000p manual]

← Older revision		Revision as of 05:15, 6 October 2021
Line 45:		Line 45:
	off). Current consumption is operational mode is ranges from 600 to 700 mA, but in		off). Current consumption is operational mode is ranges from 600 to 700 mA, but in
	sleep/power off mode less is than 100 uA		sleep/power off mode less is than 100 uA
		+
		+	== <font color="blue">Product Documentation</font> ==
		+	* [http://www.mtinst.com/wiki/upload/vna6000p_manual_cn.pdf vna6000p manual cn]
		+	* [http://www.mtinst.com/wiki/upload/vna6000p_manual.pdf vna6000p manual]

@@ Line 3: / Line 3: @@
 ✔ Frequency range: 1 MHz to 6 GHz
 ✔ Full two-port VNA: both ports can function as transmitter and receiver which allows to measure all four S-parameters without physically switching the DUT
 ✔ Above capability allows the implementation of standard VNA calibration procedures.Currently implemented procedures are 1-port OSL, 2-Port OSLT, 2-Port LMR16 and Transmission normalization for S21/S12. Industry standard models of calibration standards (separately for male and female connectors) are supported
 ✔ Due to architecture of this VNA, only one S-parameter can be measured at the time.
 Separate 1-Port and 2-Port modes are implemented. In 1-Port mode only S11 or S22 is
 measured which allows for faster trace update. In 2-port mode trace is updated after all 4
 parameters are measured successively
 ✔ Currently two traces can be displayed simultaneously which can be set to combination
 any of four S-parameters and different data representations which includes: Log
 magnitude, Linear reflection coefficient, Impedance, VSWR, Phase, Group Delay. Trace
 display range and Ref. level can be changed for all formats
 ✔ Time Domain(TD) function is available in 1-Port mode. Implemented TD modes: Band-
 Pass impulse, Low-Pass impulse ans Low-Pass step. It is possible to zoom and interpolate
 data in time axis for increased resolution
 ✔ Smith chart display is available which can be displayed simultaneously with Cartesian
 traces
 ✔ Two scrollable trace markers are available which includes 'Delta' function as well
 ✔ User can save data to Micro-SD card. Available data formats are BMP screen-shots, S-
 parameters (S1P or S2P files) and OSLT calibration coefficients. SD card also contains
 description of calibration standard model coefficients.
 ✔ Internal ('factory') calibration allows to do quick 1-Port/2-Port measurements without
 mechanical calibration
 ✔ Zero span option allows to use VNA as simple signal generator (unfiltered and level
 uncalibrated). On-board step attenuator allows to change signal power in range of 31.75
 dB with steps of 0.25 dB
 ✔ All main settings, when changed, are automatically saved in on-board EEPROM
 ✔ VNA is powered from single 3200 mA Li-Po cell or +5 to +12Vdc wall adapter and
 includes circuit for automatic battery charging. Approximate battery life ranges from 3 to